Overview
Save Big on Coursera Plus. 7,000+ courses at $160 off. Limited Time Only!
This course can also be taken for academic credit as ECEA 5341, part of CU Boulder’s Master of Science in Electrical Engineering degree.
This is our second course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled Sensors and Sensor Circuits. Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. This second course assumes that you already know how to use the kit.
After taking this course, you will be able to:
● Understand how to specify the proper AC or DC motor for a machine design.
● Integrate the motor to a machine, based on analysis of motor equations for voltage, current, torque and speed.
● Implement the motor and accompanying rotary sensor into a motor control circuit in both hardware and software.
● Add a motor and motor control circuit into a microprocessor based development kit.
● Create hardware and firmware to process motor feedback data to a microprocessor for further evaluation.
You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again.
These parts may be purchased off the Digikey web site, www. Digikey.com. Or, you may obtain the specs from the site, and purchase them elsewhere.
These are the part numbers for the above table, the lab on Motor Voltage and Current Measurement. You can copy and paste them into the search engine on the Digikey web site. You need one of each except for the AA batteries (N107-ND), which you would need 3.
428-3390-ND
P14355-ND
FQU13N10LTU-ND
N107-ND
1N5393-E3/54GICT-ND
RNF14FTD1K00CT-ND
P0.62W-1BK-ND
Additional equipment needed:
• Wire - various gauges and lengths
• Breadboard
• Oscilloscope – suggested models are:
o PICOSCOPE 2204A-D2 available on www.digikey.com or
o Digilent 410-324 | OpenScope MZ available on www.newark.com
Depending on your budget, you can also investigate these models:
o Hantek HT6022BE20MHz - https://www.amazon.com/dp/B009H4AYII
o SainSmart DSO212 - https://www.amazon.com/dp/B074QBQNB7
o PoScope Mega50 USB - https://www.robotshop.com/en/poscope-mega50-usb-mso-oscilloscope.html
o ADALM2000 - https://www.digikey.com/en/products/detail/analog-devices-inc./ADALM2000/7019661
Syllabus
- AC Motor Designs
- In module 1 you will learn principles of operation of AC induction motors, both single and 3-phase types. You well then learn how to interpret data from torque speed curves, and how to optimize data in these curves based on electrical resistance, inductance, and capacitance. Then you will learn about different types of single phase motors, featuring a video analysis of a split phase motor used in a clothing dryer. You will also learn about typical applications for single phase motors, which will assist you in picking the right one for an application.
- AC Motor Control
- In module 2 you will learn the details of AC motor specifications and enclosures, as well as how these details are governed by national and international design standards. Then you will learn a detailed methodology for researching design requirements for AC motors, and how to use these requirements to pick the right motor for your needs. Afterwards, you will have lessons on AC motor control components and systems, both manual and automatic. This will culminate in training for you on AC variable speed drives.
- DC Motors
- In module 3 you will learn principles of DC motors, traditional brushed motors, as well as electronically driven brushless motors. We will discuss shunt wound, series wound, compound wound, servo, stepper, and torque motors, with detailed explanation of how commutation and control is implemented in these designs. We will have a lab exercise for you on DC motor speed measurement. We will have another video analysis for you, this time featuring teardown of a paper shredder. Then you will learn a detailed methodology for researching design requirements for DC motors, and how to use these requirements to pick the right motor for your needs.
- DC Motor Control and Stepper Motors
- In module 4 you will start off with another lab exercise, this time gaining hands-on experience with DC motor control. Then, we will illustrate a simplified stepper motor drive, so you will understand the basic principles involved in stepper motor control. Next, you will do a deep dive into stepper motor specs, operation and commercial driver chips and packages. You will then do another lab exercise, this time on actuating a rotary sensor. We end the module with a comparison of DC vs. AC motors, so you take away a core understanding of their pros and cons.
- Course Projects
- In this module you will perform your lab work for the Course. There will be two labs
Taught by
Jay Mendelson and James Zweighaft
Tags
Reviews
4.0 rating, based on 2 Class Central reviews
4.7 rating at Coursera based on 1376 ratings
Showing Class Central Sort
-
I'm qualified electrician,need more in motor and vsd in high voltage.a and also in a motor circuit.a all basic in motor and drives circuit
-
I'm glad to take this opportunity of enrolling for this course, and this is because I in an electrical engineering services field working with motors and it's control circuits, so I think maybe by taking this opportunity will be an advantage to me.